Crease (or kink) the string at the top of the tuning-post hole toward the inside of the guitar (away from the tuning key). It shouldn't take much, just a little nudge to the side with the screwdriver … Drop the ball end of the new string in the bridge hole and replace the pin. New strings will continue to stretch (causing them to go flat) even after you tune them up to pitch. Uncoil your brand new string from its package. Do not let the For example, the environment in which you keep your guitar can cause its wooden … If you think you haven’t executed a step correctly, simply undo what you’ve done and start over. 8. As you turn the key and wind the string around the post, make sure that the string coils from the top of the post downward toward the headstock surface. 5. One difference between changing guitar strings on and acoustic versus and electric guitar is that an acoustic uses removable bridge pins to hold the strings in place at the bridge.
How to Play an E Major Chord in the Guitar, How to Tune Up a New Electric Guitar Amplifier. 6. You may have to do this three or four times, but the whole procedure shouldn’t take more than a couple minutes. Notice that this end of the string has a ball or ring shaped end. 2. After removing the peg, you will be able to pull out the other half of the broken string. 3.
Insert the string end through the appropriate tuning-post hole. Note that there is a small ball on one side of the string. Bring the string up to the proper pitch by turning the tuning key slowly. If you don’t have wire cutters available, loop the excess string into a circle or break the string by repeatedly bending the string back and forth across the crease. Pull the new string until you feel the ball end come up against the bottom of the bridge pin. If you have too much string, you’ll run out of room on the post before the string is tightened up to pitch. If that happens, simply loosen the string, pull a little more string through the post hole, re-kink the string, and begin the winding process again.
Now, replace the bridge pin back into the hole, aligning the carved slot of the pin with the string. Take it slowly. To help get the stretchiness out of the string, pull on the string gently but firmly, bringing it directly above the fingerboard, and then tune the string up to pitch by turning the key. After you remove the old strings and pull out the bridge pins, follow this process to restring your acoustic guitar: 1. Turn the tuning key so the string wraps around the post. Drop the ball end of the new string in the bridge hole and replace the pin. Tug on the string to make sure the pin doesn’t pop out, but make sure not to crease the string as you grip it for tugging. For the three lower strings, turn the tuning key so the posts rotate counterclockwise; for the three higher strings, the posts should rotate clockwise. 4. The string may want to flop around as you start to coil the string, so use your other hand to control it. Pull the new string until you feel the ball end come up against the bottom of the bridge pin. Make sure that your guitar is on a stable surface and place it on a towel so that its finish won’t get scratched. This string is brand new, and demonstrates another ball-end loop with poor workmanship. Following this procedure ensures that the strings wrap from the middle of the neck over the top of the post and to the outside of the guitar (toward the tuning key). This is a string that was made in the USA by a very well known string company. Nothing you do in stringing a guitar is permanent, even when you crease or coil a string in the process! In some cases, strings can frequently be breaking around the ball end of the guitar.. I just take a small jeweler's type screwdriver or pencil and loosen it.
3. Be sure that the string is inside the appropriate nut slot before the string becomes too taut to manipulate it further. I have a 2001 Highway 1 and some ball ends usually are stuck when I change the strings, so you didn't do anything wrong. Notice the excess string winding resting against the ball-end. Clip away the excess string sticking out of the tuning post. Pull out the peg that holds down the broken string. 4. Here, there will be six white pegs that go into the guitar body. Bridge pins require a little more fiddling to get them to secure correctly to the string in place at the bridge. Sharp Bridge. Cut the wire as close to the tuning post as your wire cutters will reach so the point doesn’t jab you in the finger!